All Credit & Thanks Goes to Rick Simpson
Visit Website http://www.phoenixtears.ca
Run from the Cure Director – Christian Laurette
From Rick Simpson :
I generally work with a pound or more of good grade hemp starting material. You can use just one ounce. An ounce will usually produce 3 or 4 grams of oil. The amount of oil produced per ounce of hemp will vary from strain to strain, but it all has that wonderful healing power.
1 – Place the completely dry starting material in a plastic bucket.
2 – Dampen the material with the solvent you are using. Many solvents can be used. You will require about two gallons of solvent to strip the THC off one pound of dry starting material. 500 milliliters of solvent should be more than enough to strip the THC from one ounce of starting material. (Editors note: For more information about which solvent to use visit the Facebook group Cannabis Oil Success Stories)
3 – Crush the plant material using a stick of clean untreated (chemical free) wood or some such device. Even though the starting material has been dampened with the solvent, you will find that the material can be readily crushed.
4 – Add solvent until the starting material is completely covered.
Use the stick to work the plant material. As you are doing this, the THC dissolves off the plant material into the solvent.
5 – Continue this process for about 3 minutes.
6 – Pour the solvent-oil mix off the plant material into another bucket. You have just stripped the plant material of about 80% of its THC.
7 – Second wash – again add solvent to the plant material and work it for another 3 minutes to get the other 20%.
8 – Pour this solvent-oil mix into the bucket containing the first mix that was poured off previously.
9 – Discard the twice-washed plant material.
10 – Pour the solvent-oil mix through a coffee filter into a clean container.
11- Boil the solvent off. I have found that a rice cooker will do this boil off very nicely. The one I have has two heat settings – high and low – and will hold over a half gallon (2.5 liters) of solvent-oil mix.
12- Add solvent-oil mix to the rice cooker until it is about ¾ full.
Make sure you are in a very well ventilated area and set up a fan to carry the solvent fumes away. The fumes are very flammable. Be sure to stay away from red-hot elements, sparks, cigarettes etc. that could ignite the fumes.
13 – Plug the rice cooker in and set it on high heat.
14 – Continue adding solvent-oil mix as the level in the rice cooker decreases until it is all in the cooker.
15 – Add a few drops of water to the solvent-oil mix as the level comes down for the last time. The amount of water added depends on how much starting material you had in the beginning. If I am producing oil from a pound of good bud, I usually add about ten drops of water.
16 – When there is about one inch of solvent-oil-water mix left in the cooker, put on your oven mitts, pick the unit up and gently swirl the contents.
17 – Continue swirling until the solvent has been evaporated off. The few drops of water help release the solvent residue and protect the oil somewhat from too much heat. When the solvent has been boiled off, the cooker that I use automatically goes to low heat. This avoids any danger of overheating the oil. At no time should the temperature of the oil go over 290F degrees (140 C).
18 – Put on your oven mitts and remove the pot containing the oil from the rice cooker.
19 – Gently pour the oil into a small stainless steel container.
20 – Place this container in a dehydrator or put in on a gentle heating device such as a coffee warmer. It may take a few hours but the water and volatile turpines will be evaporated from the oil. When there is no longer any activity on the surface of the oil the medicine is ready for use.
21 – Pour the hot oil into a bottle; or as in the video suck it up into a plastic syringe. Putting the oil in a plastic syringe makes it very easy to dispense the medicine.
When the oil cools off it has the consistency of thick grease. Some strains will produce very thick oil and you may have trouble squeezing it out of the syringe. If this happens, place the syringe in warm water a few minutes prior to use.